Training Consulting (Page 2)

Design and Development, Software and Hardware Training Resources.

A consulting firm that specializes in EMC design, troubleshooting and training services to commercial and industrial manufacturers with global distribution in the consumer, computer, network & telecommunications, industrial and scientific industries.

Kenneth Wyatt – EMC design and training services

Kenneth Wyatt - EMC design and training services

DIY 6 GHz comb generator by Kenneth Wyatt

Most simple DIY comb generators seem to run out of steam about 1 GHz. I recently ran into David Bowman’s 2.4 GHz circuit and measured an upper usable range of about 6 GHz. While greatly attenuated above 3 GHz, this circuit should still be valuable for measuring semi-anechoic chambers in the GHz ranges.

Wyatt Technical Services, LLC
56 Aspen Dr. Woodland Park, CO 80863, USA

The Canadian Standards Association is a not-for-profit membership-based association serving business, industry, government and consumers in Canada and the global marketplace.

Safety and Health Standards – CSA

CSA Group works closely with leading independent agencies and associations to promote safety standards in North America and around the world.

CSA marks confirm that a product has been tested and has met the applicable standards for safety & performance as outlined by ANSI, UL, CSA, NSF and more.

CSA Marks & Labels for North America

Special inspection for electrical health care products – “Your electric health care product is tested against the provincial guidelines Field Approval of Health Care Equipment plus any applicable CSA Group health care product standard requirements.”

Special inspection for electrical health care - CSA

Field Certification & Field Evaluation Programs

“These programs allow CSA labels to be applied to a limited run of products in the field, where ever they are used or installed in the U.S. and Canada.”

CSA Group
178 Rexdale Blvd. Toronto, ON Canada M9W 1R3

The CE marking is required for many products. It states that the product is assessed before being placed on the market and meets EU safety, health and environmental protection requirements.

CE marking – Enterprise and Industry

The CE marking (also known as CE mark) is a mandatory conformity mark on many products placed on the single market in the European Economic Area (EEA).

CE – Conformite Europeenne – Safety Standards

CE marking signifies that the product conforms with all EC directives that apply to it. For example, most electrical products must comply with the Low Voltage Directive and the EMC Directive; electrical toys must also comply with the Toy Safety Directive.

CE - Conformite Europeenne - Safety Standards

CE – European Economic Area – EEA – Safety mark

“It is the manufacturer’s responsibility to carry out the con- formity assessment, to set up the technical file, to issue the EC declaration of conformity and to affix CE marking on a product. Distributors must verify the presence of both the CE marking and the necessary supporting documentation. If the product is being imported from a third country, the importer has to verify that the manufacturer outside the EU has undertaken the necessary steps and that the documentation is available upon request.”

6 Steps to CE marking for your product – PDF

International Society for Quality Electronic Design is the pioneer and leading conference dealing with design for manufacturability and quality issues, front to back. It is now a non-profit international professional organization.

ISQED – Design and Design Automation

Targetted Audience – Researchers, Developers, and Users of EDA/TCAD Tools & Design Flows and Methodologies.

They cover Design Methods, Design Processes, Semiconductor technologies, nano-technologies,IC packaging, Test, design automation tools & methodologies..

.ISQED 2014 Theme: Security in a Connected World

ISQED - Design and Design Automation

ISQED
P.O.Box 607 Los Altos, CA 94023-0607 USA

Consulting Service for the semiconductor and microelectronic industry, FEA modeling, mechanical, electrical & materials engineering applications.

Glew Engineering – Technology Expertise

Experts in Electrical, Materials and Mechanical Engineering Consulting. Consulting and Support areas include Business Development, Solar & Flat Panel Technologies, Materials Science among many others.

FEA Applied to Semiconductor Equipment

CAD and finite element analysis (FEA)

FEA allows for comprehensive modeling of the chamber’s integrity during testing conditions. The FEA model serves as a virtual experiment that allows reduction in prototype cost and testing. An accurate model can reduce the costly repercussions of an incorrectly designed system.

(They may cover Mems and Mechatronics too. – delabs)

Glew Engineering Consulting Inc. 240 Pamela Drive, Mountain View, CA 94040 USA

High-end computerized lab equipment, accessories and sensors. They also manufacture OEM transducers, signal conditioners, industrial standards interface boards and kits. (USA Firm)

Erlich Industrial Development Corporation

Erlich Industrial Development Corporation (EID) is an OEM manufacturing and R&D Company specializing in the development of high technology biological, medical and chemical research products.

Adjustable Output Positive Voltage Power-Supply Kit

Interface board conductivity

An electronics board (kit) that allows you to connect up to 30V AC or DC on one side of the board and get adjustable VDC regulated on the other side. Every lab should have a few of these boards handy. The boards will allow you to easily power all your analog components (i.e. op-amp). The Terminal Block TB connector is included and makes it easy to use.

Interface board conductivity cell with DIN Rail clip

Interface board conductivity

Build your own Conductivity meter and/or controller and save. Simply connect your Conductivity cell (conductivity electrode, Probe) to the input via Terminal Board (TB) and the output to analog to digital converter (ADC), Digital voltmeter (DVM), Analog Voltmeter, micro-controller (MC) or PLC. Power the board and get reading.

The American National Standards Institute (ANSI) Founded – October 19 – 1918, coordinates the development and use of voluntary consensus standards in the United States and represents the needs and views of U.S. stakeholders in standardization forums around the globe.

American National Standards Institute – ANSI

Voluntary Standards Cover the Spectrum: from Multipurpose Utility Vehicles to Magnet Wire

Magnet Wire - ANSI and NEMA

Magnet Wire

Magnet wire, also known as winding wire, is an insulated copper or aluminum electrical conductor used in motors, transformers, and other electromagnetic equipment. When wound into a coil and energized, magnet wire creates an electromagnetic field for use in energy transformation as well as a wide range of communications applications and products.

American National Standards Institute (ANSI)
1899 L Street, NW 11th Floor Washington, DC 20036, USA

TÜV SÜD is an international service corporation focusing on consulting, testing, certification and training. At over 600 locations, primarily in Europe, North America, Asia Pacific,

tuv america certificate

TÜV SÜD America – Certification and Consultancy

History – Independent TÜVs Founded in the 1870’s by the German steam boiler industry.

“Technischer Überwachungsverein” means “Technical Inspection Association”

Services – Consultancy, inspections, tests and expert opinions as well as certification and training.

Objectives – Reliability, safety and quality as well as environmental protection and cost effectivenes

TÜV SÜD – Munich, Germany

TÜV SÜD Group is headquartered in Munich, Germany.